Wall Plate Encoder

All
  • AMX NMX-ENC-N1115-WP-WH, Wallplate Encoder

    AMX NMX-ENC-N1115-WP-WH, Wallplate Encoder

    $2,425.00     Add to cart

    AMX NMX-ENC-N1115-WP-WH, Wallplate Encoder

    The N1000 series encoders and decoders are an affordable local AV-over-IP switching solution that packetizes video into a minimally compressed IP format that provides excellent video quality at low latencies. This compression is perfect for point-to-point video distribution, small switching applications, and larger switching applications, all using off-the-shelf layer-3 network switches.

    • 1 lbs
    SKU: FGN1115-WP-WH Categories: , ,
    $2,425.00
  • NMX-ENC-N1115-WP Wallplate Encoder

    NMX-ENC-N1115-WP Wallplate Encoder

    $2,427.00     Add to cart

    NMX-ENC-N1115-WP Wallplate Encoder

    The N1000 Series Encoders and Decoders are an affordable local AV-over-IP switching solution that packetizes video into a minimally compressed IP format that provides excellent video quality at low latencies. This compression is perfect for point-to-point video distribution, small 2×1 switching applications, and larger switching applications (for example, 32×32), all using off-the-shelf layer-3 network switches.

    The NMX-ENC-N1115-WP provides the excellent encoding capabilities of the NMX-ENC-N1133 in a 2-gang wallplate format. This encoder can be easily mounted in a wall, lectern, or floor box using a standard 2-gang US back box, and connected to power and Ethernet using only a single category cable.

    Specifications

    Video
    • Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
    • Analog Video Input: HD-15 VGA, Component*
    • Video Output: Video Output
    • Formats: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
    • Progressive Input Resolutions
      • Supports most common HD up to 1920×1200.
    • Interlaced Input Resolutions
      • Supports 1080i60.
    • Analog Input Resolutions
      NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
      • Supports most common HD up to 1920×1200.
    • Output Resolutions: Matched to inputs.
    • Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
      NOTE: The N1115-WP does not accept Composite or S-Video (YC).
    • Color Space: 4:2:2

    *These signal types are supported through a passive adapter.
    Audio
    • Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
    • Output Signal Types: Ethernet
    • Analog Audio Format: 8ch PCM, Stereo 2-channel
    • Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
    Latency
    • Latency: 10 ms at 60 fps
    • Bandwidth: 840 Mb/s (varies with resolution)

    Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.

    Note: Scaling adds one frame of latency (17ms at 60fps).
    Communications
    • Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
    • HDMI: HDCP, EDID management
    Ports
    • P0:
      • 8-wire RJ45 female
      • 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
      • Provides the network connection, network AV video, and power to the Encoders and Decoders
    • HDMI IN: HDMI video input
    • VGA IN: DB15 analog input
    • USB IN – Host: USB-B host input
    • USB IN – Maintenance: USB-Mini maintenance input
    Controls and Indicators – Front Panel
    • RESET Button:
      • Recessed pushbutton
      • Press to initiate a ‘warm restart’ causing the processor to reset, but not lose power. A reset does NOT affect the current settings
    • POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
    • AUDIO LED: On (green) when audio is transmitting.
    • ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.
    • DIGITAL VIDEO LED: On (green) when video source is available and transmitting
    • HDCP LED: On (green) when the source is using HDCP
    • STREAM LED: On (green) when the unit is streaming video
    • STATUS LED: Flashing (green) when the unit is active.
    • LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.
    Power Supply
    • Power over Ethernet
      • Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
      • Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.

    Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.
    Environmental
    • Temperature (Operating): 32° to 104°F (0° to 40°C)
    • Temperature (Storage): -22° to 158°F (-30° to 70°C)
    • Humidity (Operating): 10% to 90% RH (non-condensing)
    • Humidity (Storage): 0% to 90% RH (non-condensing)
    • Heat Dissipation: Up to ~26 BTU/hr
    General
    • Dimensions (HWD): 4.06″ x 3.5″ x 2.25″ (10.31 cm x 8.84 cm x 5.72 cm)
    • Weight: .75 lb (0.34 kg)
    • Airflow: Natural convection via vent openings on front, back, and top
    • Installation
      • Mounts onto standard 2 gang US back boxes
      • Mounts into standard décor style wallplates (not included)
    • Regulatory Compliance: FCC, CE, and NTRL
    • Recommended Accessories
      • Compatible with NMX-ENC-N1222, NMX-ENC-N1233, NMX-ENC-N1512, and NMX-NVR-N6123
      • PS-POE-AT-TC High-Power PoE Injector, 802.3AT Compliant FG423-84)
    FG Numbers

    FGN1115-WP-WH (White)
    FGN1115-WP-BL (Black)
    SKU: FGN1115-WP-BL Categories: , ,
    $2,427.00